Just How To Install A Bathtub (For Newbies).
Just How To Install A Bathtub (For Newbies).
Blog Article
We've come across this post involving How to Install a Bathtub below on the web and figured it made sense to discuss it with you in this article.
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard project. If the old bathtub is conveniently available, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. See to it you have qualified yourself for the work and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will aid you mount a new bathtub in your restroom if you have currently gotten a brand-new bathtub and also do not require to change the arrangement of your previous supply of water pipes.
Your tools as well as material checklist must make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be quite problematic due to the restricted accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. Once the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous type must be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub ought to wait up until the bath tub has been utilized a minimum of when as this will certainly settle it into its final placement.
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can break rather early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very eager about Tools You Need to Install a New Bathtub and I hope you appreciated our page. For those who liked our page plz make sure you remember to share it. Thanks a lot for your time invested reading it.
Get An Estimate Report this page